How To Remove CPU Cooler? | Expert Guide | 2022

by
How To Remove CPU Cooler

Do you want to know how to remove CPU cooler? This guide will provide you with all the necessary information. So relax and continue reading. The CPU cooler is an important component in the computer system. The primary function of the CPU cooler is to keep the processor cool so it can work properly.

Many different types of CPUs may require more or less cooling depending on their needs, but all need some form of a CPU cooler to maintain working order.

There are three main types of CPUs: air-cooled, liquid-cooled, and phase-change cooling. If your PC uses air cooling then you will need to remove the old chip before installing a new one because there is no way for hot air to escape without opening up your case.

If you have a liquid-cooled CPU then this process is much easier. If your computer uses water cooling for the processor, just undo the hose clamps and drain any remaining fluid from the inside of your case before sliding out or disconnecting the tubing that connects to the radiator.

Then remove both side panels on your PC chassis so that there is room to slide out the CPU. You will then need to remove any brackets that keep the heatsink in place, but be careful not to bend anything since you can break parts if they are stuck or bent too far out of shape.

What is a CPU Cooler?

A CPU cooler is a device that helps reduce the operating temperature of a computer processor by removing heat. These devices can come in many shapes and sizes, but they all work on the same principle: to pull heat away from the CPU and dissipate it into the surrounding environment.

How To Remove CPU Cooler

The most common type of CPU cooler is an air-based heatsink that has fans to improve its cooling capacity. The heat generated by the processor can be dangerous to its operation, so you must have a way of dissipating this heat.

A CPU cooler does not require much maintenance and will last for years if properly maintained. It’s very easy to install one on your computer, but before you start installing check out these tips.

How to Install a CPU Cooler?

Installing a CPU cooler is an easy process that takes just a few minutes to complete. It can be frustrating if you don’t know what to do, but this article will guide you through the process step by step.

How To Remove CPU Cooler

The first thing you want to do is remove your computer’s case cover and find where the processor fan mounts on your motherboard. Once you’ve located it, make sure there are four holes around it where screws should go in.

Step By Step:-

  • Insert screws into the holes around the fan and tighten them so they won’t come loose. Make sure to not over tighten them or you might strip out one of your motherboard’s screw holes, making it unusable for more serious projects later on.
  • Place a thin layer of thermal paste onto the chip itself. This is usually a small dab in the center of the chip. Putting too much on will only make it harder to get off, so use just enough for your CPU to be covered by an extremely thin layer and you’ll do fine.
  • Place the heatsink over top of your processor and begin screwing it into place with screws that came with it or ones that are similar if they didn’t come included. Make sure not to tighten them down very far as we want some room for our fan cables later on. Connect all necessary wires from both devices (heatsink and fan) together before connecting them directly to their appropriate places within the case itself near where fans normally go inside computer cases.
  • You can also connect these two components up outside of the case before you put the cover back on. The fan should be connected to a motherboard connector that’s labeled as CPU or something similar, and your heatsink can go into any open memory slot.
  • After this is done, replace your computer’s case cover and plug it in to turn it on for the first time since installing these components inside of it. If all goes well, you will likely hear an extremely loud buzzing noise coming from either where the fans are located or near the processor itself if they’re not plugged up correctly.
  • You’ll want to quickly unplug everything until things have stopped vibrating so much just in case one of them disconnected while performing other work on your computer. Once everything has settled down after being turned off for about ten minutes, you can turn your computer back on again.
  • After checking to make sure everything is still connected tightly and that it’s making the expected noises when turned on, pat yourself on the back for successfully installing your CPU cooler.
  • You’re now ready to start overclocking if you want an even faster processor than what came with your motherboard. However, this will void any warranty you have leftover from buying the parts themselves since most companies won’t cover damage done by users attempting to push their components beyond safe levels of performance.

Conclusion

The CPU Cooler is one of the most important components in your computer, so it’s an important task to do when you build or repair computers. It’s also a good idea if your fan isn’t spinning – just be careful not to rip any cables!

We hope this article on “How To Remove CPU Cooler?” has helped clear up some confusion about how to remove and replace that pesky cooler for better airflow around your processor. If you have more questions, feel free to reach out anytime.

Thanks for reading!

Matt Booth has been playing video games professionally for over a decade. He started out as a competitive player in the Halo series, and transitioned to professional gaming with the release of Call of Duty: Modern Warfare. Since then, he has competed in countless tournaments across the globe, winning hundreds of thousands of dollars in prize money.

...

Leave a Comment